Power

PowerProtect+ uPVC IF Duct is a durable and versatile ducting system designed for Medium Voltage, High Voltage, and Shallow Burial applications. With integrated Interference-Fit sockets and a full range of accessories, it ensures secure, efficient installation across varied environments.

PowerProtect+ uPVC IF Bends provide reliable directional changes in duct routes, designed to meet typical power cable bending requirements. Each bend includes an integrated Interference-Fit socket for quick, secure, and debris-resistant connections.

uPVC Power Duct Interference Ring Seal (IRS) Socket ensures fast, secure connections while effectively preventing the ingress of dirt and water. The system is complemented by a full range of compatible bends and accessories, with customisation options available to meet specific project requirements.

uPVC Power Bend with Interference Ring Seal (IRS) Socket features a built-in IRS socket that enables quick and secure connections while preventing the ingress of dirt and water.

PowerProtect+ HDPE Duct is a durable and dependable power ducting solution, available in specifications suitable for Low to High Voltage applications.

PE Coiled Service Ducts are used within the power market for service cables and specialist applications

Emtelle Con-Duct range of ducted products enables rapid tractability of cable sheath faults within a ducted network, due to our innovative conductive coating.

Multipath is a fully developed, proven and integrated cable management system that eliminates the need to winch in sub-duct.

Multipath is a fully developed, proven and integrated cable management system that eliminates the need to winch in sub-duct.

Multipath is a fully developed, proven and integrated cable management system that eliminates the need to winch in sub-duct.

The Multipath Slip Coupler is a uPVC accessory designed for 117mm primary ducts. It comes in green and is supplied in packs of 10, providing a reliable solution for seamless duct connections.

Horizontal Directional Drilling (HDD) is a highly efficient and trenchless installation method for the underground placement of HDPE ducts and FibreFlow microduct bundles. Horizontal Directional Drilling is used where open cut installations are not feasible or the option to open trench is not advisable. It has minimal impact on the surrounding area, suitable for a variety of soil conditions and in general only requires two manholes.

Emtelle Connector Sleeves are manufactured from a solid wall uPVC duct and provide the means to connect two spigot ends of duct by sliding over one spigot and pulling back to cover the other spigot.

Push-fit End Caps prevent debris or contaminants from entering the duct system when installing cable.

Transition provide the means to connect the plain ends of two ducts with differing internal/external diameters for a smooth transition.

The duct plug can be adjusted to suit the internal diameter of a duct by hand tightening the wing nut.

Access Chambers have been designed for both footway and roadway installations, where they provide access to underground ducting.

Covers and Frames are suitably designed with manual handling requirements in mind and feature slide out covers with tapered sides for safety.

Provides a protective layer for underground ducted networks. Easy to roll over cable ducts.

Cable protection tiles are heavy duty protective boards designed to provide a protective layer for underground ducted networks.

Suitable for power, street lighting and fibre optic cables. Available with detectable wire for traceability.

DTS clips are designed to clip onto power duct to hold a DTS duct in place.

Duct brushes are used to removed dirt and debris from inside assembled duct systems.

Duct spacers are designed to assist when laying duct networks in configurations, e.g. a trefoil or grid array.

The couplers are used in install scenarios to allow for expansion/contraction between two plain ends of two ducts.

In addition to drawing cable, the foam pig can be used as a pipeline cleaning device.

The Hockey stick bends are used for domestic connections in conjunction with service coils.

The compressed seal expands into full contact with the inside duct walls thereby providing an effective, seal to your duct system in seconds.

Permanent mechanical duct and cable seals to prevent ingress of dirt and water.

Metal proving pigs are used to 'prove' the internal bore of a duct fall below a minimum diameter and has a circular profile.

Nylon proving pigs are used to 'prove' the internal bore of a duct fall below a minimum diameter and has a circular profile.

Simplex Seals consists of a thermoplastic elastomer seal, split to ease cable installation. Inner and outer wedges grasp the pipe or cable creating a rain-proof seal.

The HSI system is casted directly into the wall, for an easy duct and cable entry solution.

A cable guard is a plastic cable protection capping profile to protect cables on telegraph poles and walls.

Conduit wall fixings are used to secure duct to the side of the building.

Emtelle Double Socket Connectors are manufactured from a solid wall uPVC duct and provide the means to connect two spigot ends of duct bringing back the directional element of the sockets within the main duct run, following use of plain-ended fittings.

Emtelle Split Duct Repair Couplers provide a fast, secure solution for reconnecting or repairing split ducts, ensuring continued protection and system integrity.

Emtelle Ring Seal Couplers are manufactured from solid wall uPVC duct and provide the means to connect two plain ends of duct. Both ends of the coupler contain a ring seal to standard BSEN 681-1 (type WA).